SMC氣動執行元件（氣缸）故障    由于氣缸裝配不當和期使用，氣動執行元件（氣缸）易發生內、外泄漏，輸出力不足和動作不平穩，緩沖果不良，活塞桿和缸蓋損壞等故障現象。
1： SMC氣缸的活塞桿和缸蓋損壞，般是因活塞桿安裝偏心或緩沖機構不起作用而造成的。對此，應調整活塞桿的中心位置；更換緩沖密封圈或調節螺釘。
2：SMC氣缸的緩沖果不良，所以，當氣缸出現內、外泄漏時，應重調整活塞桿的中心，以保證活塞桿與缸筒的同軸度；須常檢查油霧器工作是否可靠，以保證執行元件潤滑良好；當密封圈和密封環出現磨損或損環時，須及時更換；若氣缸內存在雜質，應及時清除；活塞桿有傷痕時，應換。
般是因緩沖密封圈磨損或調節螺釘損壞所致。此時，應更換密封圈和調節螺釘。
3：SMC氣缸的輸出力不足和動作不平穩，般是因活塞或活塞桿被卡住、潤滑不良、供氣量不足，或缸內有冷凝水和雜質等原因造成的。對此，應調整活塞桿的中心；檢查油霧器的工作是否可靠；供氣管路是否被堵塞。當氣缸內存有冷凝水和雜質時，應及時清除。
4：SMC氣缸出現內、外泄漏，般是因活塞桿安裝偏心，潤滑油供應不足，密封圈和密封環磨損或損壞，氣缸內有雜質及活塞桿有傷痕等造成的。www.189auto.com

 SMC pneumatic actuator （cylinder） failure because improper assembly and long-term use of the cylinder, pneumatic actuator （cylinder） prone to internal and external leakage, output power and action is not smooth enough, the buffer effect of non-performing, piston rod and cylinder head damage and other symptoms .
1: SMC cylinder piston rod and cylinder head damage, usually due to the eccentric rod installation does not work or caused by the buffer body. In this regard, the center of the piston rod should be adjusted; replacement or adjustment screw ring buffer.
2: SMC cylinder adverse effect of the buffer, so when the cylinder occurs, the external leakage, should be re-adjusted the center of the piston rod, piston and cylinder to ensure concentricity; work should always check the lubricator is reliable, to ensure good lubrication actuator; when seals and sealing rings ring worn or damaged, it should be replaced; if impurities exist in the cylinder, should be promptly removed; scars on the piston rod should be replaced.
Ring buffer is generally due to wear or damage caused by adjusting screws. At this point, you should replace the seals and adjustment screws.
3: SMC cylinder output force and movement is not smooth enough, is generally due to the piston or piston rod is stuck, poor lubrication, insufficient gas supply, or the tank has condensate and impurities and other causes. In this regard, the center of the piston rod should be adjusted; check the reliability of the work of the lubricator; gas supply pipe is blocked. When the cylinder of water and impurities in the memory when there is condensation, should be promptly removed.
4: SMC cylinder occurs inside and outside the leak, usually due to installation of the eccentric rod, oil supply, seals and seal rings worn or damaged, the cylinder piston rod within the impurities and bruises caused.www.189auto.com